Litter-Robot 3 Cat Sensor - Installation Guide (2024)

WARNING:If you've determined through the troubleshooting process that you need a new cat sensor, please understand that the cat sensor is a complex system. The installation process, sensor tolerance, and calibration weight will impact its sensitivity. For these reasons, we highly recommend a base replacement or an in-house repair by Whisker where your Litter-Robot will undergo thorough testing of the cat sensor after repair. If you'd like to continue with the cat sensor installation, follow the steps below.

Litter-Robot 3 is equipped with a cat sensor, a weight-sensitive switch that detects when a cat enters and exits the globe. For the cat sensor to accurately detect your cat, your cat must weigh at least 5 lbs, or 2.3 kg, and the litter in the globe must be just below the raised fill line. Litter-Robot must be placed on firm, level flooring; avoid soft, uneven, or unstable surfaces.

You will need:

  • 1/4 inch (6,3 mm) hex socket with ratchet
  • Standard screwdriver
  • Masking tape
  • 10 lbs (or 4.5 kg) of cat litter
  • Cat sensor replacement kit

Disassemble Litter-Robot

  1. Press the Power button to turn the unit off.
    Litter-Robot 3 Cat Sensor - Installation Guide (1)
  2. Unplug the power supply from the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (2)
  3. Press the bonnet tabs on either side of the unit to release the bonnet.
    Litter-Robot 3 Cat Sensor - Installation Guide (3)
  4. Rotate the bonnet backward and lift the bonnet up to remove it from the unit.
    Litter-Robot 3 Cat Sensor - Installation Guide (4)
  5. Remove the globe and set it aside.
    Litter-Robot 3 Cat Sensor - Installation Guide (5)
  6. Remove the waste drawer and set it aside.
    Litter-Robot 3 Cat Sensor - Installation Guide (6)

Remove old cat sensor

  1. Locate the cat sensor “foot” under the base, secured by a bolt.
    Litter-Robot 3 Cat Sensor - Installation Guide (7)

  2. Look inside the base: In the back of the base, the cat sensor module is located under the metal sensor cover, secured by a nut attached to a bolt.
    Litter-Robot 3 Cat Sensor - Installation Guide (8)

    Note: The cat sensor foot is spring-loaded. Ensure that you don’t lose track of any parts as you remove the nut and bolt.

  3. While applying downward pressure into the base through either the waste port or drawer, use a 1/4 inch (6,3 mm) hex socket with ratchet to remove the 1/4 inch (6,3 mm) nut and bolt that hold the cat sensor foot to the unit.

    Litter-Robot 3 Cat Sensor - Installation Guide (9)
  4. Carefully release pressure from the base and remove the cat sensor foot and its bolt from the bottom of the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (10)

  5. Remove the metal sensor cover from inside the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (11)

  6. You should now be able to see the cat sensor module that was secured by the metal tab. It is lightly nested in its recess and secured with a plastic tab.
    Litter-Robot 3 Cat Sensor - Installation Guide (12)

  7. Unplug the cat sensor.
    Litter-Robot 3 Cat Sensor - Installation Guide (13)

  8. Slide the sensor to the side to remove it from under the plastic tab. If needed, use a screwdriver to assist you in lifting the plastic tab.
    Litter-Robot 3 Cat Sensor - Installation Guide (14)

Install new cat sensor

  1. Plug in the new cat sensor and without bending it, gently slide it under the plastic tab. Again, use a screwdriver to assist you in lifting the plastic tab if needed.
    Litter-Robot 3 Cat Sensor - Installation Guide (15)

  2. Gently place the cat sensor under the plastic tab, with the black surface facing up and the sticky adhesive surface facing down. Take care not to bend or reposition it.
    Litter-Robot 3 Cat Sensor - Installation Guide (16)

  3. Replace the spring inside the foot.
    Litter-Robot 3 Cat Sensor - Installation Guide (17)

  4. Use masking tape to hold the bolt in place inside the foot: Use one piece to create a small ball of tape to insert into the hole, and another piece of tape to keep the ball in place.

    1. Replace the cat sensor foot and bolt on the bottom of the base.
      Litter-Robot 3 Cat Sensor - Installation Guide (18)

  5. Apply pressure on the base to ensure the bolt is coming out of the hole.
    Litter-Robot 3 Cat Sensor - Installation Guide (19)

  6. Replace the metal sensor cover on top of the cat sensor.
    Litter-Robot 3 Cat Sensor - Installation Guide (20)

  7. Use your fingers to tighten the nut on the bolt, then tighten the nut with the 1/4 inch (6,3 mm) hex socket on your ratchet.
    Litter-Robot 3 Cat Sensor - Installation Guide (21)

  8. While applying downward pressure into the base to compress the spring, you'll want to tighten the nut until there is no longer any movement in the metal sensor cover. Be careful not to overtighten the bolt.
    Litter-Robot 3 Cat Sensor - Installation Guide (22)

    The sensor should be firmly fastened, but allow for a slight wiggle.

  9. Remove the tape from the cat sensor foot.
    Litter-Robot 3 Cat Sensor - Installation Guide (23)

Reassemble Litter-Robot

  1. Replace the waste drawer.
    Litter-Robot 3 Cat Sensor - Installation Guide (24)

  2. Replace the globe, ensuring it is positioned correctly. Visually check that the large gear with notches that runs around the globe is sitting in the track on the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (25)

  3. At the back of the globe, turn the black key into the key pocket.
    Litter-Robot 3 Cat Sensor - Installation Guide (26)

  4. Replace the bonnet, sliding the tabs on both sides into the slots in the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (27)

  5. Rotate the bonnet forward, aligning the tabs with the corresponding slots in the base. Snap the bonnet securely into the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (28)

  6. Plug the power supply into the base.
    Litter-Robot 3 Cat Sensor - Installation Guide (29)

  7. Press the Power button to turn the unit on.
    Litter-Robot 3 Cat Sensor - Installation Guide (30)

Successful: Once the initial clean cycle is complete, the unit should return to the home position displaying a blue “ready light” status. Proceed to the next section to calibrate the cat sensor.

Unsuccessful: If the globe is unable to complete the cycle, displaying a solid red or flashing red light, remove some litter from the globe and press the Reset button to return the globe to the home position.

Calibrate cat sensor

  1. Add approximately 10 lbs, or 4.5 kg, of cat litter to the globe. We recommend using standard-weight clay-clumping litter. This weight will be used to calibrate your unit to the new cat sensor.

    1. If you are using a standard clay-clumping litter, fill the litter just below the raised fill line. If you are using a heavier litter, fill to about halfway from the fill line.
      Litter-Robot 3 Cat Sensor - Installation Guide (31)

  2. Now press and hold the Empty andCyclebuttons for 3 seconds. This will calibrate the new cat censor.
    Litter-Robot 3 Cat Sensor - Installation Guide (32)

  3. Calibration is confirmed by the red flashing Timing LED.
    Litter-Robot 3 Cat Sensor - Installation Guide (33)

  4. Wait 30 seconds, then press the Reset button.
    Litter-Robot 3 Cat Sensor - Installation Guide (34)

    To ensure the accuracy and reliability of the cat sensor, always press the Reset button after making any changes that will affect the weight of the unit, including emptying the waste drawer, adding or removing litter from the globe, or cleaning or moving the unit. This will recalibrate the weight sensor and circuit board to reflect the changed weight.
  5. Your unit should display a solid blue light indicating it is ready for use.
    Litter-Robot 3 Cat Sensor - Installation Guide (35)

Litter-Robot 3 Cat Sensor - Installation Guide (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Frankie Dare

Last Updated:

Views: 6511

Rating: 4.2 / 5 (73 voted)

Reviews: 80% of readers found this page helpful

Author information

Name: Frankie Dare

Birthday: 2000-01-27

Address: Suite 313 45115 Caridad Freeway, Port Barabaraville, MS 66713

Phone: +3769542039359

Job: Sales Manager

Hobby: Baton twirling, Stand-up comedy, Leather crafting, Rugby, tabletop games, Jigsaw puzzles, Air sports

Introduction: My name is Frankie Dare, I am a funny, beautiful, proud, fair, pleasant, cheerful, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.